Tel: +86-371-86151827 Email: [email protected]

astm a514 grade j specs


astm a514 grade j specs

Parameters
Steel grade: astm a514 grade j specs
Specification:
Thickness: 4-200mm  
Width: 1500mm-3000mm 
Length: 6000mm-12000mm

astm a514 grade j specs Introduction

Data Sheet 1 ASTM A514 Grade B - SSAB

The flatness tolerance for as supplied product is ½ ASTM A6. ASTM A514 Grade B is supplied in the quenched and tempered condition. Fabrication and Other Recommendations Weldability Welding of A514 Grade B shall be performed in accordance with the applicable welding code.

Contact Supplier

Data Sheet 1 ASTM A514 Grade H - SSAB

General Product Description. ASTM A514 Grade H is a quenched and tempered alloy steel plate for structural applications requiring high yield strength combined with good formability and toughness. A514 Grade H has a minimum yield strength of 100 ksi [690 MPa] and may be ordered with supplemental Charpy V-notch impact test requirements.

Contact Supplier

ASTM A514 Steel Plate - Grade B, E, F, H, Q, S Leeco ...

A514 Steel Plate. ASTM A514 plate steel has a min-yield strength of 100 ksi/690 MPa. It’s most commonly used as a structural steel in building construction, for cranes, or other large machines supporting high loads. A514 is used where a weldable, machinable, very high strength steel is required to save weight or meet ultimate strength requirements.

Contact Supplier

ASTM A514 Grade Q Steel : MakeItFrom

ASTM A514 grade Q is a type of ASTM A514 steel. Cited properties are appropriate for the quenched and tempered condition. The graph bars on the material properties cards below compare ASTM A514 grade Q to wrought alloy steels in the same category (top), all iron alloys (middle), and the entire database (bottom).

Contact Supplier

ASTM A514 / A514M - 18 Standard Specification for High ...

1.1 This specification covers quenched and tempered alloy steel plates of structural quality in thicknesses of 6 in. [150 mm] and under intended primarily for use in welded structures and other non-welded structures.

Contact Supplier

ASTM-A514 - SSAB

ASTM A514. The ASTM A514 specification is the Standard Specification for High-Yield-Strength, Quenched and Tempered Alloy Steel Plate, Suitable for Welding used in applications where Yield Strengths of ≥ 100 ksi are required for plates up to 2-1/2" thick, inclusive. Plates > 2-1/2" and ≤ 6" in thickness have a minimum Yield Strength requirement...

Contact Supplier

ASTM A514 Grade A Steel : MakeItFrom

ASTM A514 grade A is a type of ASTM A514 steel. Cited properties are appropriate for the quenched and tempered condition. The graph bars on the material properties cards below compare ASTM A514 grade A to wrought alloy steels in the same category (top), all iron alloys (middle), and the entire database (bottom).

Contact Supplier

Plate - ArcelorMittal

SPECIFICATION A514†† Grade B A514† Grade E A514†† Grade F A514†† Grade H A514† Grade P A514†† Grade Q A514 Grade S Type of Steel Alloy Alloy Alloy Alloy Alloy Alloy Alloy. Requirements for Delivery A6 A6 A6 A6 A6 A6 A6. Tensile Strength (ksi) 110/130 110/130 to 2½" incl.; 100/130 over 2½- …

Contact Supplier

ASTM A514 Alloy & Abrasion Resistant Steel Plate Chapel ...

ASTM A514. A quenched & tempered, high-strength, weldable steel plate utilized in structural applications. Because of this material’s high yield strength it is ideal for projects requiring a light weight steel without sacrificing durability or toughness. Applications include truck & trailer frames, heavy construction equipment, and crane booms.

Contact Supplier

Welding ASTM A514 or A514M-05 steel? - The FABRICATOR

A514 grades are A, B, E, F, H, P, Q, and S. Each grade has a unique chemistry and may differ in the maximum thickness to which it is rolled, from 1¼ in. to 6 in. …

Contact Supplier

A514 Steel Plate - ASTM514 Abrasion Resistant Steel ...

Cutting

Contact Supplier

A514 steel - Wikipedia

A514 steel. A514 is a particular type of high strength steel, which is quenched and tempered alloy steel, with a yield strength of 100,000 psi (100 ksi or approximately 700 MPa ). The ArcelorMittal trademarked name is T-1. A514 is primarily used as a structural steel for building construction.

Specifications ·

Contact Supplier

ASTM A514 T1 Steel Plate Buy Online Cut to Size No ...

ASTM A514 T1 Steel Plate Help Print View Larger. Select Your Size Stock Size Select your size above to see available stock sizes. ... ASTM ASTM A514 (Standard Specification for High-Yield-Strength, Quenched and Tempered Alloy Steel Plate, Abrasion Resistent, Suitable for Welding) Alloy 514.

Contact Supplier

A514 Grade S,ASTM A514Gr.S ,A514 Grade S steel plate ...

The max thickness of A514 Grade S is 65mm. in the heat treatment, A514 Grade S shall be heat treatment by the mill to conform to the tensile and hardness requirements by heating to not less 900 degree and quenching in water or oil, tempering at not less 620 degree.

Contact Supplier

ASTM A514 Grade Q Steel : MakeItFrom

ASTM A514 Grade Q Steel. ASTM A514 grade Q is a type of ASTM A514 steel. Cited properties are appropriate for the quenched and tempered condition. The graph bars on the material properties cards below compare ASTM A514 grade Q to wrought alloy steels in the same category (top), all iron alloys (middle), and the entire database (bottom).

Contact Supplier

Alloy Plate - ASTM A 514 - Oliver Steel Plate

Alloy Plate - ASTM A 514 Standard specification for High-Yield-Strength, Quenched and Tempered Alloy Steel. Chemical Requirements This specification allows for fourteen different grades, each with a defined maximum thickness. The commercial market today has gravitated to four primary grades, each offering the least expensive chemistry for the thickness range covered.

Contact Supplier

ASTM-A514 Standard Specification for High-Yield …

ASTM-A514 › Standard Specification for High-Yield-Strength, Quenched and Tempered Alloy Steel Plate, Suitable for Welding. Heat and product analysis shall conform to the chemical requirements for carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, vanadium, titanium, zirconium, copper, boron, and columbium. Conformance to required mechanical properties shall be determined …

Contact Supplier

A514 - BEBON steel - A514 steel plate

A514 steel plate. ASTM A514 steel plate/sheet is a quenched and tempered high yield strength steel used in structural applications where high strength and low weight are critical.The tensile yield strength of A514 is specified as at least 100ksi (689MPa) for thicknesses up to 2.5 inched (63.5mm) thick plate,and at least 110ksi (758MPa)...

Contact Supplier

ASTM A514 Structural Steel Plate, A514 Grade A Plate, ASTM ...

ASTM A514 Grade T. ASTM A514 Grade C Steel Plates Exporters. We source our value-adding product to global businesses and applications like • Lifting and transportation industries use NFA 36-231 A514 grade structural steel plates to manufacture cranes, loaders, trucks, lorries, crushers, bulldozers, etc.

Contact Supplier

A514 Grade A,A514GrA,A514GrA STEEL

Steel plate A514 Grade A is under steel standard specification for high yield strength ASTM A514/A514M.A514GrA is alloy steel plate with quenching and tempering heat treatment when rolling.A514 Grade A is a high strength steel plate with the minimum yield strength at 690Mpa for the thickness belows 65mm,and 620 Mpa for the thickness above 65mm,the ...

Contact Supplier

ASTM A514-HENAN GANG IRON AND STEEL CO., LTD-

A514 Grade J,ASTM A514Gr.M ,A514 Grade J steel plate. ASTM A514. A514 Grade J is for high yield strength, quenched and tempered alloy steel plate of structural quality. Sept 4th. A514 Grade P,ASTM A514Gr.P,A514 Grade P steel plate.

Contact Supplier

ASTM A517 - SSAB

ASTM A517. The ASTM A517 specification is the Standard Specification for Pressure Vessel Plates, Alloy Steel, High-Strength, Quenched and Tempered material used in the application of fusion welded boilers and pressure vessels. Under this specification, the plate thickness determines the grade selection and the mechanical properties.

Contact Supplier

Steel Standards - ASTM International

List of steel standards developed by ASTM ... Standard Specification for Grade 80 and Grade 100 Alloy Steel Chain Slings for Overhead Lifting A952 / A952M - 02(2016) ... A514 / A514M - 18 Standard Specification for High-Yield-Strength, Quenched and Tempered Alloy Steel Plate, Suitable for Welding ...

Contact Supplier

ASTM A514 steel plate

ASTM A514 is mainly used as high yield strength steels for cold-forming steel s.The ASTM A514 steel is equivalent to DIN QStE690TM, NFA E690D, EN S700MC and BS 75F70 steel grades. A514 ASTM Number:1. 8974 Comparision of steel grades SEW092 Q StE 690TM NFA36-231 E690D UNI8890 - EN 101 49 -2 S700MC BS1449 75F70 Chemical Composition of A514 steel ...

Contact Supplier

A514 Grade P,A514GrP,A514GrP PLATE - Xinsteel

A514 Grade P,A514GrP. Steel plate A514 Grade P is under steel standard specification for high yield strength ASTM A514/A514M.A514GrP is alloy steel plate with quenching and tempering heat treatment when rolling.There are the similar steel grade as SA514 Grade P in steel standard ASME SA 514/SA 514M.When delivery steel materials ASTM A514Gr.P,steel...

Contact Supplier

A514 steel - Wikipedia

A514 steel. Jump to navigation Jump to search. A514 ... This is a standard set by the standards organization ASTM International, ... Specifications A514. The tensile yield strength of A514 alloys is specified as at least 100 ksi (689 MPa) for thicknesses up ...

Specifications ·

Contact Supplier

ASTM A514 T1 Steel Plate Buy Online Cut to Size No ...

ASTM ASTM A514 (Standard Specification for High-Yield-Strength, Quenched and Tempered Alloy Steel Plate, Abrasion Resistent, Suitable for Welding) Alloy 514. Characteristics Rough, rust scale finish. Workability Good candiate for some processing techniques.

Contact Supplier

For more information about the astm a514 grade j specs or if you would like to know the price, please contact us without hesitate.